Plate weight comes up on almost every job: pricing material by the pound, checking what a forklift or crane can pick, figuring freight, or knowing whether two guys can carry a base plate. The good news is that plate is the easiest shape to calculate. One number does almost all the work.
The rule of thumb: 40.8 lb per square foot per inch
Carbon steel weighs about 0.2836 lb per cubic inch (490 lb per cubic foot). A one-foot-square piece that is one inch thick holds 144 cubic inches, so it weighs 144 x 0.2836 = 40.84 lb. Every other thickness scales straight from that.
Weight (lb/sq ft) = 40.84 x thickness (in)
Piece weight (lb) = length (ft) x width (ft) x 40.84 x thickness (in)
In metric the same idea gives 7.85 kg per square metre for every millimetre of thickness, since carbon steel is about 7.85 g/cm³. A 10 mm plate is about 78.5 kg/m².
Steel plate weight chart
Weights below are calculated from nominal thickness at 0.2836 lb/in³. They match the steel plate weight chart on this site, where each size links to its own page.
| Thickness | lb/sq ft | 4' x 8' | 5' x 10' | 8' x 20' |
|---|---|---|---|---|
| 3/16" | 7.66 | 245 lb | 383 lb | 1,225 lb |
| 1/4" | 10.21 | 327 lb | 510 lb | 1,634 lb |
| 3/8" | 15.31 | 490 lb | 766 lb | 2,450 lb |
| 1/2" | 20.42 | 653 lb | 1,021 lb | 3,267 lb |
| 3/4" | 30.63 | 980 lb | 1,531 lb | 4,901 lb |
| 1" | 40.84 | 1,307 lb | 2,042 lb | 6,534 lb |
For thinner material sold by gauge, see the sheet metal gauge chart, because gauge numbers do not convert to thickness in a straight line.
Worked examples
A base plate
A 12" x 12" x 3/4" base plate is exactly one square foot, so it weighs 30.63 lb before holes. A 10" x 14" x 1/2" plate is 140 sq in, or 0.972 sq ft, so 0.972 x 20.42 = 19.9 lb.
Subtracting holes
For heavy plate with large holes, take the holes out. A hole's weight is its area times thickness times 0.2836. Four 13/16" holes in 3/4" plate remove about 4 x 0.518 sq in x 0.75 x 0.2836 = 0.44 lb. On small parts that rarely matters; on a ring or a plate with a big center cutout it can be a large share of the weight.
Parts nested from a sheet
Quote the material you buy, not just the part weight. If you need eighteen 12" x 16" gussets out of 3/8" plate, the parts weigh about 18 x 1.333 x 15.31 = 367 lb, but you are buying a full or partial plate plus the kerf and the skeleton left over. Laying the parts out in the DXF designer first shows how many fit on a sheet.
Stainless and aluminum plate
The same formula works with a different density:
- Stainless steel (304 or 316): about 0.289 lb/in³, so about 41.6 lb per sq ft per inch. That is roughly 2% heavier than carbon steel.
- Aluminum (6061 and similar alloys): about 0.0975 lb/in³, so about 14.0 lb per sq ft per inch, about one third of steel.
The steel weight calculator has a material selector for carbon steel, stainless and aluminum, and handles any plate size and quantity.
Why the scale may not match the chart
- Rolling tolerance. Mill plate is allowed to vary from nominal thickness and weight under ASTM A6/A6M, and plate often runs on the heavy side. For shipping or lifting, add a margin rather than trusting the nominal number to the pound.
- Actual vs nominal size. Plate is often sheared or flame cut a little oversize. A plate ordered 96" x 240" may arrive a bit larger.
- Cut edges and holes. Chart weights are solid rectangles.
Using plate weight in a quote
Most service centers price plate by the pound or by the hundredweight (CWT). Multiply the weight you buy by the price per pound, add cutting charges and freight, and that is your material cost. Then carry that number into the quote builder as COGS, add your markup and labor hours, and you have a price. If the job also uses tube or bar, run those lengths through the cut list optimizer so the stick count is right too.
For anything that has to hold a load, plate thickness and grade come from the drawings or the engineer, not from a weight chart.
Frequently asked questions
How much does a 4x8 sheet of 1/4 inch steel plate weigh?
About 327 lb. Quarter-inch carbon steel plate weighs about 10.21 lb per square foot, and a 4' x 8' plate is 32 square feet. Actual mill plate can run slightly heavier because of rolling tolerances.
What is the formula for steel plate weight?
Weight in pounds equals length in feet times width in feet times thickness in inches times 40.84. In metric, plate weighs about 7.85 kg per square metre for each millimetre of thickness.