Flat bar is the workhorse of a fab shop: tabs, gussets, brackets, straps, railing pickets, gate frames and base bars. Knowing its weight per foot lets you price a job, plan a lift and check a delivery. This guide gives a quick chart of common carbon steel flat bar sizes, the formula behind it, and how to use it on a real job. For every size in one place, see the full flat bar weight chart.
How flat bar sizes are called out
Flat bar is listed as thickness x width, for example 1/4" x 2". Some suppliers and drawings flip the order, so if a callout is unclear, the smaller number is almost always the thickness. Length is usually stated separately, and many suppliers stock hot rolled flat bar in 20 ft lengths, with other lengths available. Check with your supplier before you plan a cut list around a stick length.
- Hot rolled (A36 is common): slightly rounded edges and mill scale. The usual choice for structural and general fabrication.
- Cold finished (1018 is common): sharp, square edges, tighter size tolerance and a cleaner surface. Used where fit or appearance matters, at a higher cost.
Steel flat bar weight chart (lb per foot)
Weights below are for carbon steel at 0.2836 lb per cubic inch, the same basis used across the site. Actual weight can differ a little because of mill tolerances and edge shape.
| Thickness | 1" wide | 1-1/2" wide | 2" wide | 3" wide | 4" wide | 6" wide |
|---|---|---|---|---|---|---|
| 1/8" | 0.43 | 0.64 | 0.85 | 1.28 | 1.70 | 2.55 |
| 3/16" | 0.64 | 0.96 | 1.28 | 1.91 | 2.55 | 3.83 |
| 1/4" | 0.85 | 1.28 | 1.70 | 2.55 | 3.40 | 5.10 |
| 3/8" | 1.28 | 1.91 | 2.55 | 3.83 | 5.10 | 7.66 |
| 1/2" | 1.70 | 2.55 | 3.40 | 5.10 | 6.81 | 10.21 |
| 3/4" | 2.55 | 3.83 | 5.10 | 7.66 | 10.21 | 15.31 |
| 1" | 3.40 | 5.10 | 6.81 | 10.21 | 13.61 | 20.42 |
The formula for any size
You do not need a chart for odd sizes. One cubic inch of steel weighs about 0.2836 lb, and a foot of bar is 12 inches long, so:
Weight (lb/ft) = thickness (in) x width (in) x 3.40
Example: 3/8" x 5" flat bar is 0.375 x 5 x 3.40 = 6.38 lb/ft. A 20 ft stick weighs about 128 lb. For metric, multiply thickness (mm) x width (mm) x 0.00785 to get kg per metre.
If you want to skip the math, the steel weight calculator handles flat bar along with tube, angle, pipe and plate.
Other metals
The 3.40 factor is for carbon steel. For other materials, scale it by the density ratio. Stainless steel runs a little heavier than carbon steel (roughly 2 to 3 percent depending on grade), and aluminum is about one third the weight of steel. Use your supplier's published weight when the number matters for a quote or a lift.
Estimating flat bar for a job
- List every part with its size, length and quantity from the drawings.
- Nest the parts into stock lengths. Add saw kerf and trim allowance for each cut. The cut list optimizer lays parts out on sticks and shows how many to order and how much drop you will have.
- Multiply sticks by length and weight per foot to get shipping and handling weight.
- Price it. Steel is often sold by the pound or per hundredweight (CWT), so weight drives material cost. Carry that into the quote builder as your material cost.
Common mistakes
- Mixing up thickness and width when ordering. Write it the same way every time, thickness first.
- Pricing net length instead of full sticks. You pay for the drop, so quote the sticks you buy unless the drop goes to another job.
- Using flat bar where plate is the better buy. For wide, short parts like gussets or base plates, cutting from plate or ordering plate strips may be cheaper. Compare both.
- Ignoring tolerance on fit-critical parts. Hot rolled bar can be slightly off nominal. If parts must slide into a slot or a channel, measure the actual bar or use cold finished.
Always follow the drawings and specifications for material grade and size. This chart is for estimating and planning.
Frequently asked questions
How much does a 20 ft stick of 1/4 x 2 flat bar weigh?
1/4 x 2 carbon steel flat bar is about 1.70 lb per foot, so a 20 ft stick weighs about 34 lb. Actual weight can vary slightly with mill tolerance.
What is the formula for flat bar weight per foot?
Multiply thickness in inches by width in inches by 3.40. That gives pounds per foot for carbon steel. For metric, multiply thickness by width in millimetres by 0.00785 for kg per metre.